Szablon: Connectors: Różnice pomiędzy wersjami

Wersja z 13:01, 4 lut 2025

This page contains connectors description of {{{model}}} {{{type}}}.

Power supply connector

Antenna connectors

Interfaces

[[Category:{{{model}}} User Manual]]

@@ Linia 93: / Linia 93: @@
 [[File:{{{model}}}_antennasurge.png|600px|frameless|class=tlt-border]]
-      | RBMTX-Lite|RBMTX-Viper = SMA antenna connector placed on {{{gsm_place}}} panel is used to connect external GSM/UMTS/LTE. It must be connected to establish a connection with GSM/UMTS/LTE network. In good circumstances (good coverage, level of received signal is high) use antenna which is included in package. When signal strength is poor please use outdoor directional/omnidirectional or indoor antenna.
+      | RBMTX-Lite = SMA antenna connector placed on {{{gsm_place}}} panel is used to connect external GSM/UMTS/LTE. It must be connected to establish a connection with GSM/UMTS/LTE network. In good circumstances (good coverage, level of received signal is high) use antenna which is included in package. When signal strength is poor please use outdoor directional/omnidirectional or indoor antenna.
 '''''Note:''' If antenna is not connected, connection with GSM/UMTS/LTE network will be impossible.''
@@ Linia 102: / Linia 102: @@
 type is SMA male, but GNSS antenna connector type is female (the same as for GSM/UMTS/LTE antenna). There is no variant with WiFi+Bluetooth and GPIO (no space for both SMA and GPIO connectors).
-'''''Note:''' If antenna is not connected, connection with WiFi/Bluetooth network/GNSS system will be impossible. To let the router get the correct position (NMEA coordinates) put the antenna outside (in a place where the GNSS system is visible).''<br>
+'''''Note:''' If the antenna is not connected, connection with WiFi/Bluetooth network/GNSS system will be impossible. To let the router get the correct position (NMEA coordinates) put the antenna outside (in a place where the GNSS system is visible).''<br>
 '''''Note:''' Make sure you don't tighten the antenna too much. The torque setting of SMA connector is 0.15 – 0.20 NM.''
+     | RBMTX-Viper = SMA antenna connector placed on {{{gsm_place}}} panel is used to connect external GSM/UMTS/LTE. It must be connected to establish a connection with GSM/UMTS/LTE network. When signal strength is poor please use outdoor directional/omnidirectional or indoor antenna.
+'''''Note:''' If the antenna is not connected, connection with GSM/UMTS/LTE network will be impossible.''
+'''''Note:''' Make sure you don't tighten the antenna too much. The torque setting of SMA connector is 0.15 – 0.20 NM.''
+===WiFi antenna connector===
+Router is equipped with WiFi SMA male connector placed on {{{wifi_place}}} panel and it is used to connect external WiFi antenna.
+'''''Note:''' If the antenna is not connected, connection with WiFi network will be impossible.<br>
+'''''Note:''' Make sure you don't tighten the antenna too much. The torque setting of SMA connector is 0.15 – 0.20 NM.''
+[[File:{{{model}}}_antennawifi.png|400px|frameless|class=tlt-border]]
       | RBVND-Lite = SMA connector placed on back panel of device is used to connect external GSM/LTE antenna for {{{model}}}. To establish a connection with the network an external antenna must be used. Type of antenna depends on network coverage. In good circumstances (level of received signal is high) use antenna which is included in the package. If range of network signal is low or none, an outdoor directional/omnidirectional or indoor (for instance in place where signal range is sufficient) antenna should be used.