Szablon: QuickStart: Różnice pomiędzy wersjami
Z Elproma Wiki Knowledge Base
Znacznik: Ręczne wycofanie zmian |
|||
| (Nie pokazano 6 pośrednich wersji utworzonych przez tego samego użytkownika) | |||
| Linia 13: | Linia 13: | ||
Please check additional accessories in [[{{{model}}} Accessories]] | Please check additional accessories in [[{{{model}}} Accessories]] | ||
| RBMTX-Lite | | RBMTX-Lite = * Antenna (SMA connector) | ||
* Power adapter | * Power adapter | ||
* Wall holder | * Wall holder | ||
| RBMTX-Viper = * WiFi antenna (SMA connector) | |||
* Power adapter | |||
| RBVND-Lite = * Antenna (SMA connector) | | RBVND-Lite = * Antenna (SMA connector) | ||
* 20-pin cable | * 20-pin cable | ||
| Linia 292: | Linia 294: | ||
At the production stage, the device is set up with a RS232 serial interface (without the jumper inside). If there is a need to change the interface to RS485 please open the device housing and plug the jumper on the appropriate connector of the internal board (as in the picture below) and close the housing. | At the production stage, the device is set up with a RS232 serial interface (without the jumper inside). If there is a need to change the interface to RS485 please open the device housing and plug the jumper on the appropriate connector of the internal board (as in the picture below) and close the housing. | ||
[[File: | [[File:{{{model}}}_jumperrs485.png|400px|frameless|class=tlt-border]] | ||
[[File: | [[File:{{{model}}}_jumperrs232.png|400px|frameless|class=tlt-border]] | ||
}} | }} | ||
{{#ifeq: {{{usb_conf}}} | 1 | | {{#ifeq: {{{usb_conf}}} | 1 | | ||
| Linia 319: | Linia 321: | ||
{{#switch: {{{model}}} | {{#switch: {{{model}}} | ||
| RB900L3|RB900MC|RBMTX-Lite|RB900SG = * Push yellow button placed on the front panel and take | | RB900L3|RB900MC|RBMTX-Lite|RB900SG|RBMTX-Viper = * Push yellow button placed on the front panel and take SIM drawer(s) out. | ||
| RBVND-Lite = * Open the case, slide out the PCB and turn it over. | | RBVND-Lite = * Open the case, slide out the PCB and turn it over. | ||
}} | }} | ||
| Linia 332: | Linia 334: | ||
To insert the second (internal) SIM card unscrew one of the {{{type}}} panel, eject PCB board and put the SIM into internal SIM holder. | To insert the second (internal) SIM card unscrew one of the {{{type}}} panel, eject PCB board and put the SIM into internal SIM holder. | ||
| RBMTX-Viper = * Put the drawers into the {{{type}}}. | |||
| RBVND-Lite = * Put the board back to the case and close it. | | RBVND-Lite = * Put the board back to the case and close it. | ||
}} | }} | ||
| Linia 345: | Linia 348: | ||
| RB900L3|RB900MC = [[File:RB900L3_connect.png|400px|frameless|class=tlt-border]] | | RB900L3|RB900MC = [[File:RB900L3_connect.png|400px|frameless|class=tlt-border]] | ||
| RBMTX-Lite = [[File:RBMTX-Lite_gsm.png|500px|frameless|class=tlt-border]] | | RBMTX-Lite = [[File:RBMTX-Lite_gsm.png|500px|frameless|class=tlt-border]] | ||
}} | }} | ||
{{#ifeq: {{{meter}}} | 1 | | {{#ifeq: {{{meter}}} | 1 | | ||
| Linia 409: | Linia 411: | ||
1. Connect GNSS antenna to SMA connector in NTS-pico3<br> | 1. Connect GNSS antenna to SMA connector in NTS-pico3<br> | ||
2. Connect Ethernet LAN cable to RJ45 connector<br> | 2. Connect Ethernet LAN cable to RJ45 connector<br><b>WARNING: Do not connect the PoE (Power-over-Ethernet) connection to the LAN port. Otherwise it may damage the device!</b><br> | ||
3. Plug-in DC power supply to power input and turn power ON. Please check the power supply connector pinout in [[{{{model}}}_Connectors]]. | 3. Plug-in DC power supply to power input and turn power ON. Please check the power supply connector pinout in [[{{{model}}}_Connectors]]. | ||
Aktualna wersja na dzień 10:23, 12 lut 2025
This page contains instructions on how to get started with {{{model}}} {{{type}}} and how to configure it.
Package contents
Complete package contains:
- {{{model}}} {{{type}}}
[[File:{{{model}}}_package.png|500px|frameless|class=tlt-border]]
Presentation
Front
[[File:{{{model}}}_front.png|400px|frameless|class=tlt-border]]
Back
[[File:{{{model}}}_back.png|400px|frameless|class=tlt-border]]
Setting up the {{{type}}}
[[Category:{{{model}}}]]