Szablon: Connectors: Różnice pomiędzy wersjami

Z Elproma Wiki Knowledge Base
Skocz do: nawigacja, szukaj
 
(Nie pokazano 10 pośrednich wersji utworzonych przez tego samego użytkownika)
Linia 68: Linia 68:
Risk of fire or explosion or defeat the safeguard of equipment if the battery is replaced by an incorrect type. Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion. High or low extreme temperatures or low air pressure at high altitude that the battery can be subjected to during use, storage or transportation. Leaving the battery in an extremely high temperature and/or low air pressure surrounding environment that can result in an explosion or the leakage of flammable liquid or gas. Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.
Risk of fire or explosion or defeat the safeguard of equipment if the battery is replaced by an incorrect type. Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion. High or low extreme temperatures or low air pressure at high altitude that the battery can be subjected to during use, storage or transportation. Leaving the battery in an extremely high temperature and/or low air pressure surrounding environment that can result in an explosion or the leakage of flammable liquid or gas. Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.
}}
}}
{{#ifeq: {{{sim}}} | 1 | ==SIM card holder==
{{#ifeq: {{{sim}}} | 1 | ==Main SIM card holder==


External SIM card holder is placed at the front of the {{{model}}} {{{type}}} (as shown below). To insert a SIM card into the holder, press the <b>yellow button</b>, eject the black drawer, place the SIM card inside it and insert drawer into the modem (you will hear "click"). To operate the module in a GSM/LTE network, it is necessary to insert active SIM card from the network provider.
External, main SIM card holder is placed at the front of the {{{model}}} {{{type}}} (as shown below). To insert a SIM card into the holder, press the <b>yellow button</b>, eject the black drawer, place the SIM card inside it and insert drawer into the modem (you will hear "click"). To operate the module in a GSM/LTE network, it is necessary to insert active SIM card from the network provider.


[[File:{{{model}}}_connectorssim.png|400px|frameless|class=tlt-border]]
[[File:{{{model}}}_connectorssim.png|400px|frameless|class=tlt-border]]
}}<br>
}}<br>
{{#ifeq: {{{dualsim}}} | 1 | Second SIM card is located inside the device. Unscrew one of the {{{type}}} panel, eject the board and put internal SIM card into holder.
{{#ifeq: {{{dualsim}}} | 1 | Second SIM card is located inside the device. Unscrew one of the {{{type}}} panel, eject the board and put internal SIM card into holder.
}}{{#switch: {{{model}}}
    | RBMTX-Viper = Second SIM card holder (SIM2) in {{{model}}} is placed above the main SIM holder (SIM1).
NOTE: To manage SIM cards of the {{{type}}} check [[{{{model}}} Interfaces|{{{model}}} Interfaces]] and [[{{{model}}} Watchcat|{{{model}}} Watchcat]]
}}
}}
==Antenna connectors==
==Antenna connectors==


Linia 104: Linia 108:
'''''Note:''' If the antenna is not connected, connection with WiFi/Bluetooth network/GNSS system will be impossible. To let the router get the correct position (NMEA coordinates) put the antenna outside (in a place where the GNSS system is visible).''<br>
'''''Note:''' If the antenna is not connected, connection with WiFi/Bluetooth network/GNSS system will be impossible. To let the router get the correct position (NMEA coordinates) put the antenna outside (in a place where the GNSS system is visible).''<br>
'''''Note:''' Make sure you don't tighten the antenna too much. The torque setting of SMA connector is 0.15 – 0.20 NM.''
'''''Note:''' Make sure you don't tighten the antenna too much. The torque setting of SMA connector is 0.15 – 0.20 NM.''
===GPIO connector (option)===
RBMTX-Lite-IO router variant has 8-pin GPIO connector marked as “IO”. Below is the schema and pinout of GPIO connector.
[[File:{{{model}}}_gpio.png|300px|frameless|class=tlt-border]]
{{{!}} class="wikitable"; margin: auto"
{{!}}-
  ! Pin no.
  ! Signal
  ! Description
{{!}}-
  {{!}} 1
  {{!}} 3.3 V
  {{!}} -
{{!}}-
  {{!}} 2
  {{!}} IN1
  {{!}} Digital Input 1, range 0..3,3V*
{{!}}-
  {{!}} 3
  {{!}} IN2
  {{!}} Digital Input 2, range 0..3,3V*
{{!}}-
  {{!}} 4
  {{!}} IN3
  {{!}} Digital Input 3, range 0..3,3V*
{{!}}-
  {{!}} 5
  {{!}} OC1
  {{!}} Open collector Output
{{!}}-
  {{!}} 6
  {{!}} OUT1
  {{!}} Digital Output 1, range 0..3,3V
{{!}}-
  {{!}} 7
  {{!}} OUT2
  {{!}} Digital Output 2, range 0..3,3V
{{!}}-
  {{!}} 8
  {{!}} GND
  {{!}} Ground
{{!}}}
<nowiki>*</nowiki> - can be extended to Digital Input, range from 0 to max. 30V (option)
To configure or check the GPIO lines please go to "GPIO" tab in Web platform. You can read current GPIO
states or set initial states of GPIO pins. You can also add new GPIO event (one time or regular)
on all or selected pin.
     | RBMTX-Viper = SMA antenna connector placed on {{{gsm_place}}} panel is used to connect external GSM/UMTS/LTE. It must be connected to establish a connection with GSM/UMTS/LTE network. When signal strength is poor please use outdoor directional/omnidirectional or indoor antenna.
     | RBMTX-Viper = SMA antenna connector placed on {{{gsm_place}}} panel is used to connect external GSM/UMTS/LTE. It must be connected to establish a connection with GSM/UMTS/LTE network. When signal strength is poor please use outdoor directional/omnidirectional or indoor antenna.


Linia 361: Linia 417:
===LAN connector===
===LAN connector===


Second RJ-45 connector (marked as "LAN") is placed next to serial connector and is used for communication with PC or laptop through Ethernet interface. WWW configuration is available in the web browser (default IP address is 192.168.1.234). You can change the default IP address in {{{ip_address_link}}}.
Second RJ-45 connector (marked as "LAN") is placed next to serial connector and is used for communication with PC or laptop through Ethernet interface. WWW configuration is available in the web browser (default IP address is 192.168.1.234). You can change the default IP address in {{{ip_address_link}}}.<br>
<b>WARNING: Do not connect the PoE (Power-over-Ethernet) connection to the LAN port. Otherwise it may damage the device!</b>


==="R" button - factory reset===
==="R" button - factory reset===
Linia 401: Linia 458:
===Ethernet ports===
===Ethernet ports===


{{{model}}} has four Gigabit Ethernet ports (1 x WAN and 3 x LAN) marked as #1, #2, #3 and #4. The WAN interface is used to connect the router with external networks and the LAN interfaces are used to connect local networks. The WWW configuration is available in the web browser (default IP address is 192.168.1.234). You can change the default address as described in [[{{{model}}}_QuickSetup]].
{{{model}}} has four Gigabit Ethernet ports (1 x WAN and 3 x LAN). The WAN interface is used to connect the router with external networks and the LAN interfaces are used to connect local networks. The WWW configuration is available in the web browser (default IP address is 192.168.1.234). You can change the default address as described in [[{{{model}}}_Interfaces]].


===GPIO===
===GPIO===
Linia 411: Linia 468:
   ! Pin no.
   ! Pin no.
   ! GPIO
   ! GPIO
  ! Description
{{!}}-
{{!}}-
   {{!}} 1
   {{!}} 1
   {{!}}  
   {{!}} IN1
  {{!}} Isolated input
{{!}}-
{{!}}-
   {{!}} 2
   {{!}} 2
  {{!}} IN1 GND
   {{!}}  
   {{!}}  
{{!}}-
{{!}}-
   {{!}} 3
   {{!}} 3
   {{!}}  
   {{!}} IN2
  {{!}} Dry contact
{{!}}-
{{!}}-
   {{!}} 4
   {{!}} 4
   {{!}}  
   {{!}} IN3
  {{!}} Digital input 30V
{{!}}-
{{!}}-
   {{!}} 5
   {{!}} 5
   {{!}}  
   {{!}} AIN
  {{!}} Analog input
{{!}}-
{{!}}-
   {{!}} 6
   {{!}} 6
   {{!}}  
   {{!}} GND
  {{!}} Ground
{{!}}-
{{!}}-
   {{!}} 7
   {{!}} 7
   {{!}}  
   {{!}} OUT1
  {{!}} Open drain output
{{!}}-
{{!}}-
   {{!}} 8
   {{!}} 8
   {{!}}  
   {{!}} OUT2
  {{!}} Open drain output
{{!}}-
{{!}}-
   {{!}} 9
   {{!}} 9
   {{!}}  
   {{!}} OUT3
  {{!}} Relay output
{{!}}-
{{!}}-
   {{!}} 10
   {{!}} 10
  {{!}} OUT3 GND
   {{!}}  
   {{!}}  
{{!}}}
{{!}}}

Aktualna wersja na dzień 15:38, 13 mar 2025

This page contains connectors description of {{{model}}} {{{type}}}.

Power supply connector


Antenna connectors

Interfaces

[[Category:{{{model}}} User Manual]]

Źródło: „http://wiki.elpromaelectronics.com/index.php?title=Szablon:Connectors&oldid=215174”