Szablon: Connectors: Różnice pomiędzy wersjami

Aktualna wersja na dzień 15:38, 13 mar 2025

This page contains connectors description of {{{model}}} {{{type}}}.

Power supply connector

Antenna connectors

Interfaces

[[Category:{{{model}}} User Manual]]

@@ Linia 78: / Linia 78: @@
       | RBMTX-Viper = Second SIM card holder (SIM2) in {{{model}}} is placed above the main SIM holder (SIM1).
-NOTE: To manage SIM cards of the {{{type}}} check [[{{{model}}} Intefaces|{{{model}}} Intefaces]] and [[{{{model}}} QuickStart#Setting up the {{{type}}}|{{{model}}} QuickStart]]
+NOTE: To manage SIM cards of the {{{type}}} check [[{{{model}}} Interfaces|{{{model}}} Interfaces]] and [[{{{model}}} Watchcat|{{{model}}} Watchcat]]
 }}
@@ Linia 108: / Linia 108: @@
 '''''Note:''' If the antenna is not connected, connection with WiFi/Bluetooth network/GNSS system will be impossible. To let the router get the correct position (NMEA coordinates) put the antenna outside (in a place where the GNSS system is visible).''<br>
 '''''Note:''' Make sure you don't tighten the antenna too much. The torque setting of SMA connector is 0.15 – 0.20 NM.''
+===GPIO connector (option)===
+RBMTX-Lite-IO router variant has 8-pin GPIO connector marked as “IO”. Below is the schema and pinout of GPIO connector.
+[[File:{{{model}}}_gpio.png|300px|frameless|class=tlt-border]]
+{{{!}} class="wikitable"; margin: auto"
+{{!}}-
+  ! Pin no.
+  ! Signal
+  ! Description
+{{!}}-
+  {{!}} 1
+  {{!}} 3.3 V
+  {{!}} -
+{{!}}-
+  {{!}} 2
+  {{!}} IN1
+  {{!}} Digital Input 1, range 0..3,3V*
+{{!}}-
+  {{!}} 3
+  {{!}} IN2
+  {{!}} Digital Input 2, range 0..3,3V*
+{{!}}-
+  {{!}} 4
+  {{!}} IN3
+  {{!}} Digital Input 3, range 0..3,3V*
+{{!}}-
+  {{!}} 5
+  {{!}} OC1
+  {{!}} Open collector Output
+{{!}}-
+  {{!}} 6
+  {{!}} OUT1
+  {{!}} Digital Output 1, range 0..3,3V
+{{!}}-
+  {{!}} 7
+  {{!}} OUT2
+  {{!}} Digital Output 2, range 0..3,3V
+{{!}}-
+  {{!}} 8
+  {{!}} GND
+  {{!}} Ground
+{{!}}}
+<nowiki>*</nowiki> - can be extended to Digital Input, range from 0 to max. 30V (option)
+To configure or check the GPIO lines please go to "GPIO" tab in Web platform. You can read current GPIO
+states or set initial states of GPIO pins. You can also add new GPIO event (one time or regular)
+on all or selected pin.
       | RBMTX-Viper = SMA antenna connector placed on {{{gsm_place}}} panel is used to connect external GSM/UMTS/LTE. It must be connected to establish a connection with GSM/UMTS/LTE network. When signal strength is poor please use outdoor directional/omnidirectional or indoor antenna.
@@ Linia 365: / Linia 417: @@
 ===LAN connector===
-Second RJ-45 connector (marked as "LAN") is placed next to serial connector and is used for communication with PC or laptop through Ethernet interface. WWW configuration is available in the web browser (default IP address is 192.168.1.234). You can change the default IP address in {{{ip_address_link}}}.
+Second RJ-45 connector (marked as "LAN") is placed next to serial connector and is used for communication with PC or laptop through Ethernet interface. WWW configuration is available in the web browser (default IP address is 192.168.1.234). You can change the default IP address in {{{ip_address_link}}}.<br>
+<b>WARNING: Do not connect the PoE (Power-over-Ethernet) connection to the LAN port. Otherwise it may damage the device!</b>
 ==="R" button - factory reset===