Szablon: Connectors: Różnice pomiędzy wersjami

Aktualna wersja na dzień 10:47, 10 lip 2025

This page contains connectors description of {{{model}}} {{{type}}}.

Power supply connector

Antenna connectors

Interfaces

[[Category:{{{model}}} User Manual]]

@@ Linia 96: / Linia 96: @@
 [[File:{{{model}}}_antennasurge.png|600px|frameless|class=tlt-border]]
+NTS-Pico3 antenna specification:
+{{{!}} class="wikitable"; margin: auto"
+{{!}}-
+  ! Parameter
+  ! Value
+{{!}}-
+  {{!}} Frequency
+  {{!}} 1575.42 MHz
+{{!}}-
+  {{!}} Impedance
+  {{!}} 50 Ω
+{{!}}-
+  {{!}} V.S.W.R
+  {{!}} <2.0 Max
+{{!}}-
+  {{!}} Gain
+  {{!}} 38 dB
+{{!}}-
+  {{!}} Power supply
+  {{!}} 3-5VDC (10 mA)
+{{!}}-
+  {{!}} Noise fig.
+  {{!}} <1.5 dB Typ.
+{{!}}-
+  {{!}} Polarisation
+  {{!}} RHC (Right Hand Circular)
+{{!}}-
+  {{!}} Antenna type
+  {{!}} Active GPS
+{{!}}-
+  {{!}} Cable cover
+  {{!}} black
+{{!}}-
+  {{!}} Antenna cable
+  {{!}} 30m H155
+{{!}}-
+  {{!}} Connector type
+  {{!}} SMA m
+{{!}}}
       | RBMTX-Lite = SMA antenna connector placed on {{{gsm_place}}} panel is used to connect external GSM/UMTS/LTE. It must be connected to establish a connection with GSM/UMTS/LTE network. In good circumstances (good coverage, level of received signal is high) use antenna which is included in package. When signal strength is poor please use outdoor directional/omnidirectional or indoor antenna.
@@ Linia 108: / Linia 149: @@
 '''''Note:''' If the antenna is not connected, connection with WiFi/Bluetooth network/GNSS system will be impossible. To let the router get the correct position (NMEA coordinates) put the antenna outside (in a place where the GNSS system is visible).''<br>
 '''''Note:''' Make sure you don't tighten the antenna too much. The torque setting of SMA connector is 0.15 – 0.20 NM.''
+===GPIO connector (option)===
+RBMTX-Lite-IO router variant has 8-pin GPIO connector marked as “IO”. Below is the schema and pinout of GPIO connector.
+[[File:{{{model}}}_gpio.png|300px|frameless|class=tlt-border]]
+{{{!}} class="wikitable"; margin: auto"
+{{!}}-
+  ! Pin no.
+  ! Signal
+  ! Description
+{{!}}-
+  {{!}} 1
+  {{!}} 3.3 V
+  {{!}} -
+{{!}}-
+  {{!}} 2
+  {{!}} IN1
+  {{!}} Digital Input 1, range 0..3,3V*
+{{!}}-
+  {{!}} 3
+  {{!}} IN2
+  {{!}} Digital Input 2, range 0..3,3V*
+{{!}}-
+  {{!}} 4
+  {{!}} IN3
+  {{!}} Digital Input 3, range 0..3,3V*
+{{!}}-
+  {{!}} 5
+  {{!}} OC1
+  {{!}} Open collector Output
+{{!}}-
+  {{!}} 6
+  {{!}} OUT1
+  {{!}} Digital Output 1, range 0..3,3V
+{{!}}-
+  {{!}} 7
+  {{!}} OUT2
+  {{!}} Digital Output 2, range 0..3,3V
+{{!}}-
+  {{!}} 8
+  {{!}} GND
+  {{!}} Ground
+{{!}}}
+<nowiki>*</nowiki> - can be extended to Digital Input, range from 0 to max. 30V (option)
+To configure or check the GPIO lines please go to "GPIO" tab in Web platform. You can read current GPIO
+states or set initial states of GPIO pins. You can also add new GPIO event (one time or regular)
+on all or selected pin.
       | RBMTX-Viper = SMA antenna connector placed on {{{gsm_place}}} panel is used to connect external GSM/UMTS/LTE. It must be connected to establish a connection with GSM/UMTS/LTE network. When signal strength is poor please use outdoor directional/omnidirectional or indoor antenna.