Szablon:Textcommands

This page contains the list of text commands supported by {{{model}}} {{{type}}} and its description.

All below commands are available from 3.0.x modem firmware version. They can be send over USB, SMS or Teleorigin Manager.

Special characters: <EXT> - End of Text 0x03 character <CR> - Carriege Return 0x0D character <LF> - Line Feed 0x0A character

NOTE: <CR><LF> characters can be omitted when the command is sent via SMS and Teleorigin Manager („Console” tab).

Device commands

RB900SG Commands
Available since firmware version: 3.0.0
RB900SG GET FW VERSION<CR><LF>	Downloads the firmware version number of the microcontroller
Response	x.x.x<CR><LF> where x – version number
Response example	3.0.0<CR><LF>
RB900SG GET IP<CR><LF>	Retrieves the IP address of the device
Response	x.x.x.x<CR><LF>
Response example	10.43.210.2<CR><LF>
RB900SG GET RTCTIME<CR><LF>	Gets device time in Unix time or unless the clock is out of sync then rtc time is equal uptime
Response	xxxx<CR><LF>
Response example	868<CR><LF>
RB900SG GET UPTIME<CR><LF>	Gets the number of seconds since the device startup
Response	xxxx<CR><LF>
Response example	868<CR><LF>
RB900SG RESET<CR><LF>	Resets the device
Response	-
Response example	-
RB900SG TIME<CR><LF>	Returns the current time in human-readable version
Response	Time: xxxxxxxxxx, mm-dd-yyyy hh:mm:ss<CR><LF>
Response example	Time: 1619618224, 11-30-2021 13:57:04 <LF><CR><LF>
RB900SG LOG PRINT<CR><LF>	Sends all entries from the event log
Response	------------------------------------------------------ Sep 12:30:05 - x.x.x<CR><LF> Sep 12:30:08 - SIM ready<CR><LF> Sep 12:30:09 - Cfg port opened<CR><LF> Sep 12:30:11 - PDP activated<CR><LF>
Response example	------------------------------------------------------ Sep 12:30:05 - x.x.x<CR><LF> Sep 12:30:08 - SIM ready<CR><LF> Sep 12:30:09 - Cfg port opened<CR><LF> Sep 12:30:11 - PDP activated<CR><LF> Sep 12:30:12 - IP: 46.77.88.87 Sep 12:30:14 - Sync to NTP
RB900SG LOG FORMAT<CR><LF>	Removes all entries from the event log
Response	OK<CR><LF>
Response example	As above
RB900SG GET HW VERSION<CR><LF>	Downloads the hardware version number of the device
Response	x.x.x<CR><LF> where x – version number
Response example	2.3.1<CR><LF>
RB900SG BATTERY VOLTAGE<CR><LF>	Downloads battery voltage in volts
Response	X.XX<CR><LF>
Response example	4.08<CR><LF>
RB900SG GET TEMPERATURE<CR><LF>	Downloads temperature of the device
Response	XX.X *C<CR><LF>
Response example	30.5 *C<CR><LF>

Allowlist commands

PHONE ALLOWLIST Commands
Available since firmware version: 3.0.0
PHONE ALLOWLIST ENABLE<CR><LF><CR><LF>	Turns allowlist on
Response	OK<CR><LF>
Response example	As above
PHONE ALLOWLIST DISABLE<CR><LF>	Turns allowlist off
Response	OK<CR><LF>
Response example	As above
PHONE ALLOWLIST STATUS<CR><LF>	Returns information whether allowlist is on or off
Response	xxxxxxx<CR><LF>
Response example	DISABLE<CR><LF>
PHONE ALLOWLIST LIST<CR><LF>	Returns a list of numbers added to an allowlist
Response	Phone allow list is empty or xxxxxxxxx +xxxxxxxxxxxx xxxxxxxxxxxxxx<CR><LF>
Response example	Phone allow list is empty or 123456789 +0012123456789<CR><LF>
PHONE ALLOWLIST ADD <phone_number><CR><LF>	Adds a <phone_number> to the allowlist Where: <phone_number> - phone numer in national or international format NOTE: it is recomended to add the numer in national and international format separately (without and with the area code)
Response	OK<CR><LF>
Response example	As above
PHONE ALLOWLIST REMOVE <phone_number><CR><LF>	Removes the given <phone_number> from the allowlist Where: <phone_number> - phone numer in national or international format
Response	OK<CR><LF>
Response example	As above
PHONE ALLOWLIST CLEAR<CR><LF>	Removes all phone numbers from allowlist
Response	OK<CR><LF>
Response example	As above

Config commands

CONFIG Commands
Available since firmware version: 3.0.0
CONFIG SET APN <apn> <username> <password><CR><LF>	Sets <apn> Where: <apn> - string with Access Point Name <username> - apn username (optional) <password> - apn password (optional)
Response	OK<CR><LF>
Response example	As above
CONFIG GET APN<CR><LF>	Returns apn and username (optional) and password (optional)
Response	Xxxxxxxxx xxxxxxxx xxxxxxxx<CR><LF>
Response examples	internet <CR><LF> or internet username password<CR><LF> Where: internet is <apn> username is <username> password is <password>
CONFIG SET TCP PORTS <data_port> <config_port><CR><LF>	Sets TCP ports (data and config) Where: <data_port> - TCP data port (range from 0 to 65535) <config_port> - TCP port for remote configuration (range from 0 to 65535)
Response	OK<CR><LF>
Response example	As above
CONFIG GET TCP PORTS<CR><LF>	Returns TCP <data_port> and <config_port> ports
Response	xxx xxx<CR><LF>
Response example	703 704<CR><LF> Where: 703 is <data_port> and 704 is <config_port>
CONFIG SET SIM PIN <pin><CR><LF>	Sets the PIN code of the SIM card Where: <pin> - PIN code of the SIM card (range from 0000 to 9999)
Response	OK<CR><LF>
Response example	As above
CONFIG GET SIM PIN<CR><LF>	Returns the PIN code of the SIM card
Response	xxxx<CR><LF>
Response example	1111<CR><LF>
CONFIG SET ANTENNA <type><CR><LF>	Sets the antenna to external or internal <type> Where: <type> - type of antenna, options: EXTERNAL INTERNAL
Response	OK<CR><LF>
Response example	As above
CONFIG GET ANTENNA<CR><LF>	Returns the antenna type
Response	xxxxxxxxx<CR><LF>
Response example	EXTERNAL<CR><LF>
CONFIG SET PERIODIC REBOOT <start_time><CR><LF>	Sets the periodic restart time Where: - restart time in hours (from 0 to 8760). When it is set to 0, the device will not perform periodic reboot <start_time> - Unix time* - optional. If it is ommited, <start_time> equals device startup time - there will be added also the HH:MM format option (under development)
Response	OK<CR><LF>
Response example	As above
CONFIG GET PERIODIC REBOOT<CR><LF>	Returns periodic restart time and start time in hours
Response	x xxxxxxxxxx<CR><LF>* - there will be added also x xx:xx format option (under development)
Response example	1 1619515560<CR><LF>* Where: 1 is 1619515560 is <start_time> - there will be added also 1 10:30 format option (under development)
CONFIG SET UART <configuration><CR><LF>	Configures UART Where: <configuration> - configuration string in the format xxxx abc where xxxx = baudrate, a = start bits, b = parity, c = stop bits
Response	OK<CR><LF>
Response example	As above
CONFIG GET UART<CR><LF>	Returns UART configuration
Response	xxxx xxx<CR><LF>
Response example	9600 8N1<CR><LF> Where: 9600 is baudrate 8 is start bits N is parity 1 is stop bits
CONFIG SET TEXT INFO 1 <CR><LF>	Sets text information Where: - string with additional comment (up to 128 characters)
Response	OK<CR><LF>
Response example	As above
CONFIG GET TEXT INFO 1<CR><LF>	Returns text information
Response	Xxxxxx<CR><LF>
Response example	Test comment<CR><LF>
CONFIG SET RTC SOURCE <source><CR><LF>	Sets the internal clock sync source Where: <source> - clock source, options: GSM (time from GSM network) NTP ntp_addr ntp_port (time from NTP server, ntp_addr – string with NTP server address, ntp_port – NTP port (range from 0 to 65535), optional, usually 123)
Response	OK<CR><LF>
Response example	As above
CONFIG GET RTC SOURCE<CR><LF>	Returns the internal clock synchronization source
Response	xxx<CR><LF>
Response examples	GSM<CR><LF> or NTP ntp.elproma.com.pl 123<CR><LF>
CONFIG SET NETWORK SEARCH MODE <mode><CR><LF>	Sets the network search mode Where: <mode> - AUTO or 2G or 3G or 4G sets the search mode to auto, 2G (GSM) only, 3G (WCDMA) only or 4G (LTE) only
Response	OK<CR><LF>
Response example	As above
CONFIG GET NETWORK SEARCH MODE<CR><LF>	Returns the network search mode
Response	xx<CR><LF>
Response example	2G<CR><LF>
CONFIG SAVE<CR><LF>	Saves configuration to device memory
Response	OK<CR><LF>
Response example	As above
CONFIG SET SERIAL TYPE <type><CR><LF>	Sets serial port hardware layer type where: <type> - 232 or 422 or 485
Response	OK<CR><LF>
Response example	As above
CONFIG GET SERIAL TYPE<CR><LF>	Returns serial port hardware layer type
Response	XXX<CR><LF>
Response example	232<CR><LF>
CONFIG SET WATCHDOG PING SERVER <en> <addr> <timeout> <ping_num><CR><LF>	Sets options for pinging external server, where: <en> - enable (0 or 1), <addr> - address (max. 32 chars), <timeout> - timeout in seconds 1-255 (optional), <ping_num> - number of ping repetitions 1-10 (optional)
Response	OK<CR><LF>
Response example	As above
CONFIG GET WATCHDOG PING SERVER<CR><LF>	Returns options for pinging external server
Response	xxxxxxx<CR><LF> or <domain or IP> <timeout> <ping_num>
Response example	DISABLE<CR><LF> or domain.com 20 4
CONFIG RESET<CR><LF>	Resets configuration requires CONFIG SAVE and reset of the device (RB900SG RESET) to apply
Response	OK<CR><LF>
Response example	As above
Available since firmware version: 3.0.3
CONFIG SET VPN <option><CR><LF>	Sets VPN on or off where: <option> - ENABLE or DISABLE
Response	OK<CR><LF>
Response example	As above
CONFIG GET VPN<CR><LF>	Returns VPN status
Response	xxxxxxx<CR><LF>
Response example	ENABLE<CR><LF> or DISABLE<CR><LF>