Szablon: QuickStart: Różnice pomiędzy wersjami
Z Elproma Wiki Knowledge Base
| (Nie pokazano 11 pośrednich wersji utworzonych przez tego samego użytkownika) | |||
| Linia 13: | Linia 13: | ||
Please check additional accessories in [[{{{model}}} Accessories]] | Please check additional accessories in [[{{{model}}} Accessories]] | ||
| RBMTX-Lite | | RBMTX-Lite = * Antenna (SMA connector) | ||
* Power adapter | * Power adapter | ||
* Wall holder | * Wall holder | ||
| RBMTX-Viper = * WiFi antenna (SMA connector) | |||
* Power adapter | |||
| RBVND-Lite = * Antenna (SMA connector) | | RBVND-Lite = * Antenna (SMA connector) | ||
* 20-pin cable | * 20-pin cable | ||
| Linia 29: | Linia 31: | ||
}} | }} | ||
[[File:{{{model}}}_package.png|500px| | [[File:{{{model}}}_package.png|500px|frameless|class=tlt-border]] | ||
{{#ifeq: {{{variants}}} | 1 | | {{#ifeq: {{{variants}}} | 1 | | ||
| Linia 280: | Linia 282: | ||
===Front=== | ===Front=== | ||
[[File:{{{model}}}_front.png|400px| | [[File:{{{model}}}_front.png|400px|frameless|class=tlt-border]] | ||
===Back=== | ===Back=== | ||
[[File:{{{model}}}_back.png|400px| | [[File:{{{model}}}_back.png|400px|frameless|class=tlt-border]] | ||
==Setting up the {{{type}}}== | ==Setting up the {{{type}}}== | ||
| Linia 292: | Linia 294: | ||
At the production stage, the device is set up with a RS232 serial interface (without the jumper inside). If there is a need to change the interface to RS485 please open the device housing and plug the jumper on the appropriate connector of the internal board (as in the picture below) and close the housing. | At the production stage, the device is set up with a RS232 serial interface (without the jumper inside). If there is a need to change the interface to RS485 please open the device housing and plug the jumper on the appropriate connector of the internal board (as in the picture below) and close the housing. | ||
[[File: | [[File:{{{model}}}_jumperrs485.png|400px|frameless|class=tlt-border]] | ||
[[File: | [[File:{{{model}}}_jumperrs232.png|400px|frameless|class=tlt-border]] | ||
}} | }} | ||
{{#ifeq: {{{usb_conf}}} | 1 | | {{#ifeq: {{{usb_conf}}} | 1 | | ||
| Linia 315: | Linia 317: | ||
* Disconnect the USB cable after setting up the device. | * Disconnect the USB cable after setting up the device. | ||
}} | }} | ||
{{#ifeq: {{{wireless}}} | 1 | | {{#ifeq: {{{wireless}}} | 1 | | ||
===Inserting SIM cards=== | ===Inserting SIM cards=== | ||
{{#switch: {{{model}}} | {{#switch: {{{model}}} | ||
| RB900L3|RB900MC|RBMTX-Lite|RB900SG = * Push yellow button placed on the front panel and take | | RB900L3|RB900MC|RBMTX-Lite|RB900SG|RBMTX-Viper = * Push yellow button placed on the front panel and take SIM drawer(s) out. | ||
| RBVND-Lite = * Open the case, slide out the PCB and turn it over. | | RBVND-Lite = * Open the case, slide out the PCB and turn it over. | ||
}} | }} | ||
[[File:{{{model}}}_sim1.png|400px| | [[File:{{{model}}}_sim1.png|400px|frameless|class=tlt-border]] | ||
* Place the SIM card in the holder as shown in the picture. | * Place the SIM card in the holder as shown in the picture. | ||
[[File:{{{model}}}_sim2.png|400px| | [[File:{{{model}}}_sim2.png|400px|frameless|class=tlt-border]] | ||
{{#switch: {{{model}}} | {{#switch: {{{model}}} | ||
| Linia 334: | Linia 334: | ||
To insert the second (internal) SIM card unscrew one of the {{{type}}} panel, eject PCB board and put the SIM into internal SIM holder. | To insert the second (internal) SIM card unscrew one of the {{{type}}} panel, eject PCB board and put the SIM into internal SIM holder. | ||
| RBMTX-Viper = * Put the drawers into the {{{type}}}. | |||
| RBVND-Lite = * Put the board back to the case and close it. | | RBVND-Lite = * Put the board back to the case and close it. | ||
}} | }} | ||
| Linia 345: | Linia 346: | ||
}} | }} | ||
{{#switch: {{{model}}} | {{#switch: {{{model}}} | ||
| RB900L3|RB900MC = [[File:RB900L3_connect.png|400px| | | RB900L3|RB900MC = [[File:RB900L3_connect.png|400px|frameless|class=tlt-border]] | ||
| RBMTX-Lite = [[File:RBMTX-Lite_gsm.png|500px| | | RBMTX-Lite = [[File:RBMTX-Lite_gsm.png|500px|frameless|class=tlt-border]] | ||
}} | }} | ||
{{#ifeq: {{{meter}}} | 1 | | {{#ifeq: {{{meter}}} | 1 | | ||
| Linia 364: | Linia 364: | ||
To mount the {{{type}}} inside the meter housing, please use one of the handles. The available handles are shown in the photos below. | To mount the {{{type}}} inside the meter housing, please use one of the handles. The available handles are shown in the photos below. | ||
[[File:{{{model}}}_holder1.png|400px| | [[File:{{{model}}}_holder1.png|400px|frameless|class=tlt-border]] | ||
[[File:{{{model}}}_holder2.png|400px| | [[File:{{{model}}}_holder2.png|400px|frameless|class=tlt-border]] | ||
The method of mounting the modem in the ITRON SL7000 housing is shown in the photo below. | The method of mounting the modem in the ITRON SL7000 housing is shown in the photo below. | ||
[[File:{{{model}}}_insidemeter.png|500px| | [[File:{{{model}}}_insidemeter.png|500px|frameless|class=tlt-border]] | ||
}} | }} | ||
| Linia 378: | Linia 378: | ||
Installing a basic system will require the following (a) '''mounting of the antenna''' (b) optionally '''mounting 1 or 2 lightning arrestors''' (not included to product set). The antenna supplied is of the active type, and is suitable for almost all applications. It is supplied with a pre-attached, 30-meter H-155 coax cable, terminated with a male SMA connector. Before commencing installation, check that all the items detailed in the contents list have been supplied. The antenna is supplied with mounting clamps for attachment to a mounting pole, included too. Mast antenna suspension (H=0.5m) is not included but it is available as separate products from Elproma. Following figure shows an example of how mounting antenna might be achieved. | Installing a basic system will require the following (a) '''mounting of the antenna''' (b) optionally '''mounting 1 or 2 lightning arrestors''' (not included to product set). The antenna supplied is of the active type, and is suitable for almost all applications. It is supplied with a pre-attached, 30-meter H-155 coax cable, terminated with a male SMA connector. Before commencing installation, check that all the items detailed in the contents list have been supplied. The antenna is supplied with mounting clamps for attachment to a mounting pole, included too. Mast antenna suspension (H=0.5m) is not included but it is available as separate products from Elproma. Following figure shows an example of how mounting antenna might be achieved. | ||
[[File:{{{model}}}_antenna_mounting.png|600px| | [[File:{{{model}}}_antenna_mounting.png|600px|frameless|class=tlt-border]] | ||
<span style="color:red">Note:</span> The most important consideration in selecting a position for the antenna is the presence of objects which obscure the sky or horizon. Where possible, there should be no obstruction to a full view of the sky. | <span style="color:red">Note:</span> The most important consideration in selecting a position for the antenna is the presence of objects which obscure the sky or horizon. Where possible, there should be no obstruction to a full view of the sky. | ||
| Linia 390: | Linia 390: | ||
As the antenna is roof mounted (to have a clear view of the sky) it is likely to be exposed to lightning strikes. | As the antenna is roof mounted (to have a clear view of the sky) it is likely to be exposed to lightning strikes. | ||
[[File:{{{model}}}_lightning_protection.png|600px| | [[File:{{{model}}}_lightning_protection.png|600px|frameless|class=tlt-border]] | ||
Protection against this is afforded by ensuring adequate grounding of the mountings as described below. There is no way to provide 100% protection for electronic equipment from direct strike damage. It is possible however, to reduce the likelihood of damage from near strike induced fields by ensuring the installation obeys some fundamental rules. | Protection against this is afforded by ensuring adequate grounding of the mountings as described below. There is no way to provide 100% protection for electronic equipment from direct strike damage. It is possible however, to reduce the likelihood of damage from near strike induced fields by ensuring the installation obeys some fundamental rules. | ||
| Linia 402: | Linia 402: | ||
All connections should incorporate as large an area of contact as possible, which is made more probable using large bolts, and substantial washers. Where there is no access to the metal framework of the building, it is imperative to erect a suitable lightning conductor. Failure to do so is almost certain to result in destruction of '''{{{model}}}''' and connected into it equipment in the event of the antenna receiving a near lightning strike. | All connections should incorporate as large an area of contact as possible, which is made more probable using large bolts, and substantial washers. Where there is no access to the metal framework of the building, it is imperative to erect a suitable lightning conductor. Failure to do so is almost certain to result in destruction of '''{{{model}}}''' and connected into it equipment in the event of the antenna receiving a near lightning strike. | ||
[[File:{{{model}}}_grounding.png|600px| | [[File:{{{model}}}_grounding.png|600px|frameless|class=tlt-border]] | ||
[[File:{{{model}}}_surge_protection.png|600px| | [[File:{{{model}}}_surge_protection.png|600px|frameless|class=tlt-border]] | ||
[[File:{{{model}}}_surge_protection2.png|600px| | [[File:{{{model}}}_surge_protection2.png|600px|frameless|class=tlt-border]] | ||
===Powering up=== | ===Powering up=== | ||
1. Connect GNSS antenna to SMA connector in NTS-pico3<br> | 1. Connect GNSS antenna to SMA connector in NTS-pico3<br> | ||
2. Connect Ethernet LAN cable to RJ45 connector<br> | 2. Connect Ethernet LAN cable to RJ45 connector<br><b>WARNING: Do not connect the PoE (Power-over-Ethernet) connection to the LAN port. Otherwise it may damage the device!</b><br> | ||
3. Plug-in DC power supply to power input and turn power ON. Please check the power supply connector pinout in [[{{{model}}}_Connectors]]. | 3. Plug-in DC power supply to power input and turn power ON. Please check the power supply connector pinout in [[{{{model}}}_Connectors]]. | ||
Aktualna wersja na dzień 10:23, 12 lut 2025
This page contains instructions on how to get started with {{{model}}} {{{type}}} and how to configure it.
Package contents
Complete package contains:
- {{{model}}} {{{type}}}
[[File:{{{model}}}_package.png|500px|frameless|class=tlt-border]]
Presentation
Front
[[File:{{{model}}}_front.png|400px|frameless|class=tlt-border]]
Back
[[File:{{{model}}}_back.png|400px|frameless|class=tlt-border]]
Setting up the {{{type}}}
[[Category:{{{model}}}]]