Szablon: Connectors: Różnice pomiędzy wersjami

Wersja z 11:17, 13 gru 2022

This page contains connectors description of {{{model}}} {{{type}}}.

Power supply connector

Antenna connectors

GSM antenna connector

Interfaces

[[Category:{{{model}}} User Manual]]

@@ Linia 27: / Linia 27: @@
 [[File:RB900L3_powersupplypinout.png|100px|border|class=tlt-border]]
+'''''NOTE:''' The device is switched off by removing the external power supply from the electric socket. The electric socket must be located close to the device and easily accessible.''
 ==SIM card holder==
@@ Linia 48: / Linia 50: @@
 [[File:RB900L3_antennagsm.png|400px|border|class=tlt-border]]
+     | RBMTX-Lite = SMA antenna connector placed on front panel is used to connect external GSM/UMTS/LTE. It must be connected to establish a connection with GSM/UMTS/LTE network. In good circumstances (good coverage, level of received signal is high) use antenna which is included in package. When signal strength is poor please use outdoor directional/omnidirectional or indoor antenna.
+'''''Note:''' If antenna is not connected, connection with GSM/UMTS/LTE network will be impossible.''
+'''''Note:''' Make sure you don't tighten the antenna too much. The torque setting of SMA connector is 0.15 – 0.20 NM.''
+===WiFi + Bluetooth and GNSS antenna connector (option)===
+Router can be optionally equipped with WiFi+Bluetooth or GNSS receiver (select the appropriate router variant when ordering). SMA antenna connector placed on back panel is used to connect external WiFi+Bluetooth or GNSS antenna. WiFi+Bluetooth antenna connector
+type is SMA male, but GNSS antenna connector type is female (the same as for GSM/UMTS/LTE antenna).
+'''''Note:''' If antenna is not connected, connection with WiFi/Bluetooth network/GNSS system will be impossible. To let the router get the correct position (NMEA coordinates) put the antenna outside (in a place where the GNSS system is visible).''
+'''''Note:''' Make sure you don't tighten the antenna too much. The torque setting of SMA connector is 0.15 – 0.20 NM.''
       | RBVND-Lite = SMA connector placed on back panel of device is used to connect external GSM/LTE antenna for {{{model}}}. To establish a connection with the network an external antenna must be used. Type of antenna depends on network coverage. In good circumstances (level of received signal is high) use antenna which is included in the package. If range of network signal is low or none, an outdoor directional/omnidirectional or indoor (for instance in place where signal range is sufficient) antenna should be used.
@@ Linia 142: / Linia 157: @@
    {{!}} Ring Indicator
 {{!}}}
+     | RBMTX-Lite = ===Router serial port, either full RS232/RS485===
+Serial RS232/RS485 (RJ-45 connector marked as “RS232/485”) is placed on front panel of router. Serial connector pinout is described in a tables below:
+{{{!}} class="wikitable" style="text-align: center; margin: auto"
+{{!}}-
+  ! RS232/RS485 signal
+  ! RJ45 connector
+{{!}}-
+  {{!}} A
+  {{!}} 1
+{{!}}-
+  {{!}} 5V
+  {{!}} 2
+{{!}}-
+  {{!}} B
+  {{!}} 3
+{{!}}-
+  {{!}} GND
+  {{!}} 4
+{{!}}-
+  {{!}} TX
+  {{!}} 5
+{{!}}-
+  {{!}} RX
+  {{!}} 6
+{{!}}-
+  {{!}} RTS
+  {{!}} 7
+{{!}}-
+  {{!}} CTS
+  {{!}} 8
+{{!}}}
+===LAN connector===
+Second RJ-45 connector (marked as “LAN”) is placed next to serial connector and is used for communication with PC or laptop through Ethernet interface. WWW configuration is available in the web browser (default IP address is 192.168.1.234). You can change the default address in [RBMTX-Lite_QuickSetup].
       | RBVND-Lite =