Szablon: Connectors: Różnice pomiędzy wersjami
Z Elproma Wiki Knowledge Base
| Linia 58: | Linia 58: | ||
===WiFi + Bluetooth and GNSS antenna connector (option)=== | ===WiFi + Bluetooth and GNSS antenna connector (option)=== | ||
Router can be optionally equipped with WiFi+Bluetooth or GNSS receiver (select the appropriate router variant when ordering). SMA antenna connector placed on back panel is used to connect external WiFi+Bluetooth or GNSS antenna. WiFi+Bluetooth antenna connector | Router can be optionally equipped with WiFi+Bluetooth or GNSS receiver (select the appropriate router variant when ordering). SMA antenna connector placed on back panel is used to connect external WiFi+Bluetooth or GNSS antenna. WiFi+Bluetooth antenna connector | ||
type is SMA male, but GNSS antenna connector type is female (the same as for GSM/UMTS/LTE antenna). | type is SMA male, but GNSS antenna connector type is female (the same as for GSM/UMTS/LTE antenna). There is no variant with WiFi+Bluetooth and GPIO (no space for both SMA and GPIO connectors). | ||
'''''Note:''' If antenna is not connected, connection with WiFi/Bluetooth network/GNSS system will be impossible. To let the router get the correct position (NMEA coordinates) put the antenna outside (in a place where the GNSS system is visible).'' | '''''Note:''' If antenna is not connected, connection with WiFi/Bluetooth network/GNSS system will be impossible. To let the router get the correct position (NMEA coordinates) put the antenna outside (in a place where the GNSS system is visible).''<br> | ||
'''''Note:''' Make sure you don't tighten the antenna too much. The torque setting of SMA connector is 0.15 – 0.20 NM.'' | '''''Note:''' Make sure you don't tighten the antenna too much. The torque setting of SMA connector is 0.15 – 0.20 NM.'' | ||
| RBVND-Lite = SMA connector placed on back panel of device is used to connect external GSM/LTE antenna for {{{model}}}. To establish a connection with the network an external antenna must be used. Type of antenna depends on network coverage. In good circumstances (level of received signal is high) use antenna which is included in the package. If range of network signal is low or none, an outdoor directional/omnidirectional or indoor (for instance in place where signal range is sufficient) antenna should be used. | | RBVND-Lite = SMA connector placed on back panel of device is used to connect external GSM/LTE antenna for {{{model}}}. To establish a connection with the network an external antenna must be used. Type of antenna depends on network coverage. In good circumstances (level of received signal is high) use antenna which is included in the package. If range of network signal is low or none, an outdoor directional/omnidirectional or indoor (for instance in place where signal range is sufficient) antenna should be used. | ||
| Linia 191: | Linia 191: | ||
Second RJ-45 connector (marked as “LAN”) is placed next to serial connector and is used for communication with PC or laptop through Ethernet interface. WWW configuration is available in the web browser (default IP address is 192.168.1.234). You can change the default address in [[RBMTX-Lite_QuickSetup]]. | Second RJ-45 connector (marked as “LAN”) is placed next to serial connector and is used for communication with PC or laptop through Ethernet interface. WWW configuration is available in the web browser (default IP address is 192.168.1.234). You can change the default address in [[RBMTX-Lite_QuickSetup]]. | ||
===GPIO=== | |||
Standard version of {{{type}}} (without WiFi+Bluetooth) can have GPIO connector marked as "IO". Below is the schema and pinout of | |||
8-pin GPIO connector. | |||
[[File:gpio_pinout.png|400px|border|class=tlt-border]] | |||
* - can be extended to Digital Input, range from 0 to max. 30V (option) | |||
| RBVND-Lite = | | RBVND-Lite = | ||
Wersja z 10:53, 14 gru 2022
This page contains connectors description of {{{model}}} {{{type}}}.
Power supply connector
Antenna connectors
GSM antenna connector
Interfaces
[[Category:{{{model}}} User Manual]]