Szablon: Connectors: Różnice pomiędzy wersjami
Z Elproma Wiki Knowledge Base
| Linia 30: | Linia 30: | ||
'''''NOTE:''' The device is switched off by removing the external power supply from the electric socket. The electric socket must be located close to the device and easily accessible.'' | '''''NOTE:''' The device is switched off by removing the external power supply from the electric socket. The electric socket must be located close to the device and easily accessible.'' | ||
| RB900SG = The power supply connector marked as ''PWR'' is a 2-pin connector for external DC power supply connection, which can handle voltage from range 5..30 V DC, 2.5 W max. continuous power. (for modem with internal battery). | | RB900SG|RB900SG-ElpOS = The power supply connector marked as ''PWR'' is a 2-pin connector for external DC power supply connection, which can handle voltage from range 5..30 V DC, 2.5 W max. continuous power. (for modem with internal battery). | ||
[[File:{{{model}}}_powersupply.png|400px|border|class=tlt-border]] | [[File:{{{model}}}_powersupply.png|400px|border|class=tlt-border]] | ||
| Linia 56: | Linia 56: | ||
<span style="color:red">Attention!</span> | <span style="color:red">Attention!</span> | ||
Please note that it is prohibited to connect external power supply and the meter at the same time, as the power pins of power port and RJ45 port are internally shorted. | Please note that it is prohibited to connect external power supply and the meter at the same time, as the power pins of power port and RJ45 port are internally shorted. | ||
In order to power the | In order to power the {{{model}}} from external source and communicating with the meter at the same time it is needed to prepare the proper cable, in which the pin 1 has to be removed. | ||
===Battery disposal=== | ===Battery disposal=== | ||
The | The {{{model}}} terminal contains a Li-Po battery. | ||
<span style="color:red">SAFETY INFORMATION:</span> | <span style="color:red">SAFETY INFORMATION:</span> | ||
| Linia 80: | Linia 80: | ||
{{#switch: {{{model}}} | {{#switch: {{{model}}} | ||
| RB900L3|RB900MC|RB900SG|RBMTX-Lite|RBMTX-Viper = ===GSM antenna connector=== | | RB900L3|RB900MC|RB900SG|RB900SG-ElpOS|RBMTX-Lite|RBMTX-Viper = ===GSM antenna connector=== | ||
}} | }} | ||
{{#switch: {{{model}}} | {{#switch: {{{model}}} | ||
| RB900L3|RB900MC|RB900SG = SMA “ANT” input is used to connect external GSM/LTE antenna. To establish a connection with a GSM/LTE network, an external antenna must be used. Type of antenna depends of GSM/LTE coverage. In good circumstances (level of received signal is high) use antenna contained in the package. If the range of GSM/LTE is low or none, an outdoor or indoor (for instance in place where GSM/LTE range is sufficient) antenna should be used.<br> | | RB900L3|RB900MC|RB900SG|RB900SG-ElpOS = SMA “ANT” input is used to connect external GSM/LTE antenna. To establish a connection with a GSM/LTE network, an external antenna must be used. Type of antenna depends of GSM/LTE coverage. In good circumstances (level of received signal is high) use antenna contained in the package. If the range of GSM/LTE is low or none, an outdoor or indoor (for instance in place where GSM/LTE range is sufficient) antenna should be used.<br> | ||
'''''Note:''' If there is no antenna connected to SMA connector, the connection with GSM/LTE network is impossible.'' | '''''Note:''' If there is no antenna connected to SMA connector, the connection with GSM/LTE network is impossible.'' | ||
| Linia 105: | Linia 105: | ||
}} | }} | ||
{{#switch: {{{model}}} | {{#switch: {{{model}}} | ||
| RB900L3|RBMTX-Viper = ===GPS/GNSS antenna connector=== | | RB900L3|RBMTX-Viper = ===GPS/GNSS antenna connector=== | ||
Wersja z 13:49, 12 kwi 2024
This page contains connectors description of {{{model}}} {{{type}}}.
Power supply connector
Antenna connectors
Interfaces
[[Category:{{{model}}} User Manual]]